Radius协议规定的标准停止计费原因
Radius协议规定的标准停止计费原因
用户下线原因说明
Radius协议规定的标准停止计费原因
编码 | 原因解释 | 备注 |
|---|---|---|
1 | User request to offline | 用户主动下线 |
2 | Lost carrier | 数据中断 |
3 | Lost service | 业务中断 |
4 | Idle timeout | 空闲超时 |
5 | Session timeout | 会话超时 |
6 | Admin reset | 管理员重置 |
7 | Admin reboot | 管理员要求下线 |
8 | Port error | 端口故障 |
9 | Nas error | NAS 故障 |
10 | Nas request to offline | NAS要求下线 |
11 | Nas reboot | NAS重启 |
12 | Port unneeded | 端口停用 |
13 | Port preempted | 端口被抢占 |
14 | Port suspend | 端口挂起 |
15 | Service unavailable | 业务不支持 |
16 | Callback user | 回叫业务 |
17 | User info error | 用户信息有误 |
18 | Host request to offline | 主机主动下线 |
华为自定义下线原因
对应的Radius标准原因码 | Subcode | 原因解释 | 备注 |
|---|---|---|---|
SC_PROTOCOL_USER_REQUEST (1) | 19 | User request to offline | 用户主动下线 |
21 | PPP user request | 用户主动下线 | |
34 | EAPOL user request | 用户正常下线 | |
65 | Web user request | 用户主动下线 | |
69 | DHCP release | 收到用户的RELEASE报文 | |
70 | DHCP decline | 收到用户的DECLINE报文 | |
95 | FTP with user switch | FTP用户切换其使用用户帐户 | |
110 | Gateway different from former | ARP或者IP报文触发上线场景,检测到网关地址和预期IP不一致 | |
156 | L2TP request offline | CM请求L2TP用户下线 | |
168 | WLAN cuts DHCP old user | WLAN用户上线将原来的DHCP用户下线 | |
272 | Realloc ip timeout | 二次地址分配等待RELEASEIP超时 | |
273 | Lease renewal timeout for short-leased users | 短租期用户更新租期超时 | |
367 | Mac user ppp preferred | 用户使能了同一MAC优先PPP功能(使能命令:AAA视图命令mac-user ppp-preferred)后MAC冲突导致DHCP用户下线 | |
435 | Radius client request | Radius客户端请求下线 | |
555 | Receive LCP terminate request from user while LCP negotiating. | LCP协商阶段收到用户LCP终止请求 | |
556 | Receive LCP terminate request from user after IPCP negotiation. | IPCP协商后收到用户LCP终止请求 | |
558 | Receive PADT packet from user. | 收到用户PADT报文 | |
SC_PROTOCOL_LOST_CARRIER(2) | 22 | PPP with echo fail | echo握手失败 |
29 | ARP with detect fail | ARP探测失败 | |
36 | EAPOL with echo fail | 握手失败 | |
49 | WEBS with heartbeat fail | 心跳超时 | |
162 | Tunnel with session null | 收到对方HELLO报文但是 本端无会话 | |
166 | No response of control packet from peer | 发送控制报文超过报文最大重传次数 | |
177 | ND Detect Fail | ND探测失败 | |
275 | DHCP with MTU limit | MTU限制 | |
432 | L2TP wait control ack from peer timeout | L2TP等待对端控制回应报文超时 | |
SC_PROTOCOL_LOST_SERVICE (3) | 27 | LNS request | LNS发起的连接拆除 |
152 | L2TP peer cleared tunnel | LNS清除隧道 | |
154 | LNS cleared session | LNS清除会话 | |
155 | LNS clearing session error | LNS清除会话报文解析错误 | |
SC_PROTOCOL_IDLE_TIMEOUT(4) | 90 | Idle cut | 闲置切断 |
SC_PROTOCOL_SESSION_TIMEOUT (5) | 88 | AAA with flow limit | 流量的闲置切断用户下线 |
93 | Session time out | 时间的闲置切断 | |
SC_PROTOCOL_ADMIN_RESET (6) | 40 | SRVCFG cut command | 二层或者三层专线在线时卸载命令行(BAS口视图命令access-type layer2-leased-line user-name <uname> password { cipher <cipher-password> | simple <simple-password> } [ bas-interface-name <bname> | default-domain authentication <dname> | accounting-copy radius-server <rd-name> | nas-port-type <port-type> ] * 和 access-type layer3-leased-line { user-name <uname> | user-name-template } password { cipher <cipher-password> | simple <simple-password> } [ bas-interface-name <bname> | default-domain authentication <dname> | accounting-copy radius-server <rd-name> | nas-port-type <port-type> | mac-address <mac-address> | client-id <client-id> ] *)导致的用户下线 |
87 | AAA cut command | 通过AAA视图的cut?access-user命令行删除用户 | |
91 | AAA with radius server cut command | RADIUS服务器明确传来的指令性切断 | |
158 | CLI clear tunnel | 命令行(用户视图命令reset l2tp tunnel lac { tunnel-name <remote-name> | tunnel-item <tunnel-item> } [ session <session-id> ] | remote-address <ip-address> [ l2tp-group <group-name> ]或者reset l2tp tunnel lns slot <slot-id> { tunnel-name <remote-name> | tunnel-item <tunnel-item> } )发起用户下线 | |
SC_PROTOCOL_PORT_ERROR (8) | 59 | CM with Ifnet down | 接口Down |
102 | Board remove | 接口板拔出 | |
103 | Card remove | 卡拔出 | |
104 | Slot down | 单板Down | |
148 | PPP pvc interface down | PVC 端口Down | |
149 | PPP VE interface down | VE端口Down | |
353 | CM with Ifnet ipv6 protocol down | 接口协议Down | |
SC_PROTOCOL_NAS_ERROR (9) | 79 | AAA with message send fail | 发送消息失败 |
159 | L2TP checking SCCRP error | 检查SCCRP报文有错误 | |
160 | L2TP checking ICRP error | 检查ICRP报文有错误 | |
SC_PROTOCOL_NAS_REQUEST (10) | 1 | User request to offline | 用户主动下线 |
2 | Lost carrier | 数据中断 | |
3 | Lost service | 业务中断 | |
4 | Idle timeout | 空闲超时 | |
5 | Session timeout | 会话超时 | |
6 | Admin reset | 管理员重置 | |
7 | Admin reboot | 管理员要求下线 | |
8 | Port error | 端口故障 | |
9 | Nas error | NAS 故障 | |
10 | Nas request to offline | NAS要求下线 | |
11 | Nas reboot | NAS重启 | |
12 | Port unneeded | 端口停用 | |
13 | Port preempted | 端口被抢占 | |
14 | Port suspend | 端口挂起 | |
15 | Service unavailable | 业务不支持 | |
16 | Callback user | 回叫业务 | |
17 | User info error | 用户信息有误 | |
18 | Host request to offline | 主机主动下线 | |
25 | PPPOE with ethernet interface down | 以太接口DOWN导致PPPOE用户下线 | |
26 | L2TP with cut command | L2TP发起的连接拆除 | |
33 | Interface down | 接口Down | |
41 | MCC with IGMP request | IGMP模块请求下线 | |
43 | MCC with route delete | 路由老化 | |
44 | MCC with IGMP disable | IGMP协议关闭 | |
45 | MCC with level 2 devise leaving | 二层设备离开 | |
46 | MCC with PVLAN Attribute change | 基于port+vlan下组播属性配置发生变化 | |
48 | MCC with MG attribute change | 组播组的属性发生变化 | |
50 | Webs with Realloc IP Address fail | 二次地址分配失败 | |
51 | AM with lease timeout | 租期到删除用户 | |
53 | AM with Renew lease timeout | 续租失败 | |
54 | CM with l2tp session fail | 会话建立失败 | |
55 | CM with login fail | logoin失败 | |
57 | CM with access limit | 接入限制 | |
58 | CM with time out | CM模块定时器超时 | |
60 | CM with IP address alloc fail | 地址分配失败 | |
67 | DHCP with server nak | 收到DHCP服务器的NAK报文 | |
68 | DHCP with server no response | DHCP服务器无响应 | |
71 | DHCP with IP address conflict | IP地址冲突 | |
74 | AAA with logout fail | logout失败 | |
75 | AAA with force MG offline fail | 强制组播离线失败 | |
77 | AAA with user information error | 用户在线过程中所记录信息被异常修改,无法继续进行上线处理 | |
78 | AAA with realtime accouting fail | 实时记费失败 | |
80 | AAA reauthen stop accounting | 重认证时,停止前一个域的计费 | |
81 | Server trigger reauthen stop accounting | 服务器触发的重认证时,停止前一个域的计费 | |
82 | AAA with start accounting fail | 开始记费失败 | |
83 | AAA with Authentication no response | 认证超时 | |
84 | AAA with authorization data error | 授权的数据错误 | |
86 | AAA access limit | 接入限制 | |
89 | AAA with local bill pool no space | 本地计费的话单池已经满了 | |
92 | AAA with stop accounting fail | 停止计费失败 | |
94 | AAA with update fail | 业务控制属性实时更新失败触发切断 | |
96 | FTP with service closing | FTP服务正在关闭 | |
97 | FTP with server closed | FTP server 被停止 | |
98 | FTP with server idle timeout | FTP服务超时 | |
99 | FTP with user login fail | 用户登陆失败 | |
100 | FTP with receive data fail | 读入FTP协议数据失败 | |
101 | Interface delete | 接口删除 | |
105 | IP address conflict | 添加IP HASH失败 | |
106 | MAC address conflict | 添加MAC HASH失败 | |
108 | DHCP wait client packet timeout | 等待客户端发送报文超时 | |
119 | DHCP illegal ip range | 不正确的IP范围 | |
121 | DHCP invalid IP pool info | 地址池/服务器信息不可用 | |
122 | DHCP storing pool info failed | 存储地址池/服务器信息不可用 | |
130 | DHCP receive discover from a working user | 收到已上线用户发来的DISCOVER报文,导致该用户下线(正常流程) | |
135 | AAA with radius decode fail | Radius解析属性失败 | |
139 | DHCP lease timeout | DHCP用户租期超时 | |
142 | Layer2-VPN down | 二层VPN连接Down | |
143 | Board on Master removed | 接口板拔出 | |
144 | Card on Master removed | 子卡拔出 | |
145 | Interface on Master down | 接口Down | |
146 | PPP negotiate fail | PPP协商失败 | |
150 | VPDN license not enable | VPDN license不允许 | |
151 | Authenticate fail | CM认证失败 | |
161 | LNS challenge us but password is null | LNS端挑战本端,但是无密码 | |
164 | L2TP send ICRQ fail | 发送ICRQ时失败 | |
165 | L2TP send ICCN fail | 发送ICCN时失败 | |
169 | PPP user over LNS request | PPP请求下线 | |
170 | LAC clear tunnel | LAC清除隧道 | |
171 | LAC clear session | LAC清除会话 | |
172 | CLI clear tunnel | 命令行发起用户下线 | |
173 | LNS clear tunnel | LNS清除隧道 | |
174 | LNS clear session | LNS清除会话 | |
175 | LNS send fail | LNS发送失败 | |
176 | LNS clear group | 清除对应的l2tp-group | |
182 | RUI user request offline | RUI用户主动下线 | |
183 | MP main users offline, then cut all sub users | MP用户主用户下线导致的子用户下线 | |
184 | MP sub user down | MP子用户异常导致的主用户Down | |
185 | Netmask assigned by RDS error(Route conflict) | RADIUS针对PPP用户下发掩码, 与设备上路由冲突 | |
186 | Netmask assigned by RDS error(Value invalid) | RADIUS针对PPP用户下发掩码, 与设备地址池中地址冲突 | |
189 | VRRP change to slave | 由于VRRP由主变成备,备设备上PPP用户直接下线 | |
190 | The domain has not bound ip-pool or ipv6-pool | 域下无可用地址 | |
199 | Not config prefix in domain | IPv6用户上线,域下未配置前缀 | |
200 | CM with Framed IP address invalid | PPP下发的地址本地存在 | |
203 | Unmatched Vpn-Instance | VPN实例不匹配 | |
205 | Domain disable remote backup | 域未使能远端备份, 备升主删除用户 | |
207 | local no this user | Local不存在该帐号 | |
208 | AAA send authen request fail | 认证请求发送失败 | |
209 | Local authen reject | Local 认证拒绝 | |
210 | Local author reject | Local 授权拒绝 | |
213 | layer2 leased line config delete | 由于二层专线配置被删除,所以将其下的所有用户删除 | |
271 | DHCP repeat packet | 收到用户的重复报文 | |
274 | Dhcp server speed limit | 服务器报文达到上线速率限制 | |
278 | RUI request offline | RUI用户请求下线 | |
303 | Not bind IPv6 pool or ip alloc fail | 域下没有配置IPv6地址池或ip分配失败 | |
304 | UCM failed to apply resource for trunk user | 更新trunk用户资源失败 | |
305 | UCM failed to update work-slot of trunk-interface user | 用户 更新Trunk用户工作槽位失败 | |
306 | UCM failed to update QoS resource of trunk-interface user | ace user 更新trunk用户Qos源失败 | |
319 | DHCPV6 wait UCM timeout | DHCPV6等待UCM回应超时 | |
320 | DHCPV6 wait client timeout | DHCPV6等待客户端回应超时 | |
321 | DHCPV6 ip alloc fail | DHCPV6 ip分配失败 | |
322 | DHCPV6 client decline | DHCPV6 客户端拒绝分配的ip | |
323 | DHCPV6 client release | DHCPV6 客户端释放分配的ip | |
325 | Block domain force user to offline | 域阻塞强制用户下线 | |
326 | CM with AAA auth ack time out | CM等待AAA认证回应超时 | |
329 | CM with AMV6 ipv6 ack time out | CM等待AM v6回应超时 | |
330 | CM with AM ip ack time out | CM等待AM v4回应超时 | |
331 | CM with PPP conn up time out | CM等待PPP 连接up回应超时 | |
332 | CM with DHCPACC conn up time out | CM等待DHCP连接up回应超时 | |
333 | CM with DHCPv6 conn up time out | CM等待DHCPV6连接up回应超时 | |
334 | CM with MSEADA cib ack time out | CM等待适配下发cib回应超时 | |
335 | CM with ARP detect ack time out | CM等待ARP探测回应超时 | |
336 | CM with AAA ipv6 update ack time out | CM等待AAA更新 v6回应超时 | |
337 | CM with AAA logout ack time out | CM等待AAA logout 回应超时 | |
338 | CM with WEB logout resp time out | CM等待WEB logout 响应超时 | |
339 | CM with MSEADA update workslot time out | CM等待适配更新工作槽位回应超时 | |
341 | DHCPV6 wait server timeout | DHCPV6服务器超时 | |
352 | DHCPV6 lease expired | DHCPV6租期到期 | |
365 | Author of IP address and ip include conflict | 记录域下include配置错误 | |
366 | CM with PPP ipv6 conn up time out | PPP IPV6 用户连接超时 | |
381 | IP alloc fail for trigger user | ARP/IP/RUI触发用户地址分配失败 | |
382 | Radius alloc incorrect IP | RADIUS下发的IP错误 | |
386 | AMV6 with assigning ipv6 address conflicted | AMV6分配ipv6地址冲突 | |
387 | DHCPV6 repeat solicit | DHCPV6重复solict | |
388 | CM with DHCPv6 conn request time out | CM模块等待DHCPv6模块连接请求消息超时 | |
389 | The vrf of domain is not accord with the pool | 域下配置的vpn与地址池下配置的不一致 | |
392 | CGN Board reset | CGN单板重启 | |
416 | Receive L2TP Session break message from peer LAC | 收到对端LAC备份的会话拆除消息 | |
417 | Receive L2TP Tunnel break message from peer LAC | 收到对端LAC备份的隧道拆除消息 | |
422 | L2TP tunnel idle cut | L2TP 隧道闲置切断 | |
528 | Fail to get AP MAC | 获取AP MAC地址失败 | |
529 | Get unnumbered loopback failed | 获取借用网关地址错误 | |
530 | RADIUS server delivered the denial of renewal flag | Radius下发拒绝续租终止 | |
541 | Session group virtual user offline | session group虚用户下线 | |
560 | OFFER packet contains a gateway IP address | SERVER在OFFER报文中给用户分配的IP地址是网关IP | |
561 | OFFER packet contains an IP address not on user segment | OFFER中分配的IP地址不属于用户所在网段 | |
562 | OFFER packet contains an IP address being used | 正在使用的IP地址被OFFER报文分配给了其他用户 | |
563 | OFFER packet contains a conflicting IP address | OFFER报文中给用户分配的IP地址正在被他人使用 | |
564 | OFFER packet has an IP address being used by PPPoE user | OFFER中分配的IP地址被PPPoE用户占用 | |
564 | OFFER packet has an IP address being used by PPPoE user | OFFER中分配的IP地址被PPPoE用户占用 | |
565 | ACK packet contains a gateway IP address | ACK报文中分配的IP地址是网关IP | |
566 | ACK packet contains an IP address being used | 正在使用的IP地址被ACK报文分配给了其他用户 | |
566 | ACK packet contains an IP address being used | 正在使用的IP地址被ACK报文分配给了其他用户 | |
567 | ACK packet contains a conflicting IP address | ACK报文中给用户分配的IP地址正在被他人使用 | |
567 | ACK packet contains a conflicting IP address | ACK报文中给用户分配的IP地址正在被他人使用 | |
568 | ACK packet has an IP address being used by PPPoE user | ACK中分配的IP地址被PPPoE用户占用 | |
568 | ACK packet has an IP address being used by PPPoE user | ACK中分配的IP地址被PPPoE用户占用 | |
569 | RADIUS allocated address not matching the trigger one | RADIUS下发的IP地址与触发用户不一致 | |
569 | RADIUS allocated address not matching the trigger one | RADIUS下发的IP地址与触发用户不一致 | |
570 | No available pool for the Layer3 DHCP user | 三层DHCP用户找不到可用地址池 | |
570 | No available pool for the Layer3 DHCP user | 三层DHCP用户找不到可用地址池 | |
571 | No available pool for the Layer2 DHCP user | 二层DHCP用户找不到可用地址池 | |
571 | No available pool for the Layer2 DHCP user | 二层DHCP用户找不到可用地址池 | |
572 | Server-Identifier in packet is not the local device | SERVER IDENTIFIER非设备上的IP | |
572 | Server-Identifier in packet is not the local device | SERVER IDENTIFIER非设备上的IP | |
573 | DHCP wait authentication reply timeout | DHCP等待认证超时 | |
574 | DHCP wait Up reply timeout | DHCP等待UP超时 | |
575 | Fail to alloc specified IP address for RUI | RUI备机分配指定IP地址失败 | |
576 | No available pool | 无可用地址池 | |
576 | No available pool | 无可用地址池 | |
577 | The idle addresses conflict with those used by other users | 空闲的IP地址实际被设备其他用户占用 | |
577 | The idle addresses conflict with those used by other users | 空闲的IP地址实际被设备其他用户占用 | |
578 | ACK contains a gateway IP address not matching the user's | ACK报文中携带的网关与用户的网关不匹配 | |
578 | ACK contains a gateway IP address not matching the user's | ACK报文中携带的网关与用户的网关不匹配 | |
579 | ACK packet contains a mask not matching the user's | ACK报文中的掩码与用户掩码不一致 | |
579 | ACK packet contains a mask not matching the user's | ACK报文中的掩码与用户掩码不一致 | |
580 | DHCP Server no response. | DHCP服务器无响应 | |
581 | ACK packet contains an IP address not on user segment | ACK中分配的IP地址不在用户网段内 | |
581 | ACK packet contains an IP address not on user segment | ACK中分配的IP地址不在用户网段内 | |
582 | ACK packet has an IP address being used by other user | ACK中分配的IP地址被其他人占用 | |
583 | IP address record fail on local device | 本地记录远端分配的IP地址失败 | |
586 | The memory reached the restart threshold | 内存达到重启门限值 | |
594 | Deny padi by ACL | ACL拒绝padi报文 | |
595 | Pppoe chasten | PPPoE 惩罚 | |
596 | Fail to process padi | 处理pdai报文失败 | |
597 | Fail to process padr | 处理padr报文失败 | |
598 | Drop padi or padr for backup rui | RUI备机丢弃padi报文或者padr报文 | |
599 | Packet version or type is wrong | 报文类型错误 | |
600 | Create pppinfo fail | 创建ppp信息失败 | |
601 | Deny discover packet by ACL | ACL拒绝discovery报文 | |
602 | Drop discover packet for ip pool is synchronizing | 地址池信息正在同步,丢弃discovery报文 | |
603 | Drop discover packet with Option54 | 根据option54信息丢弃discovery报文 | |
604 | Fail to process DHCP Discover packet | 处理discovery报文失败 | |
640 | User have no overlap pool | 用户没有可用的overlap地址池 | |
655 | No available pool for DHCPV6 | DHCPV6没有可用地址池 | |
656 | IPv6 address is over limit | IPv6地址数超过规格 | |
657 | IPv6 address is over limit on slot | IPv6地址数超过单板规格 | |
658 | User is over IP stack limit | 用户超过IP栈规格 | |
659 | GTL license limit | GTL license 限制 | |
665 | The number of users exceeds limit | 当前用户数已超出整机限制 | |
666 | This device does not support bas | 此设备不支持用户上线 | |
667 | CGN instance down | CGN实例状态不可用 | |
669 | Master slot of CGN instance is unavailable | CGN实例主板不可用 | |
674 | Physical link down. | 链路DOWN | |
675 | Number of users exceeded the spec which the device is able to support | 接入用户数超过设备所能支持的最大用户 | |
675 | Number of users exceeded the spec which the device is able to support | 接入用户数超过设备所能支持的最大用户 | |
676 | Update PPP user conflict with others | 更新PPP用户时和其他PPP用户冲突 | |
677 | Update PPP user, it reached the MAC session limit | 更新PPP用户时达到了1个MAC会话数限制 | |
679 | Get a challenge from peer LNS, but the password of local tunnel is null | 获得对端LNS的challenge,但本地隧道密码为空 | |
682 | Framing capability is invalid from LNS SCCRP | LNS SCCRP的Framing capability无效 | |
683 | Receive window size is invalid from LNS SCCRP | 从LNS SCCRP接收的窗口尺寸无效 | |
684 | Receive unsupported AVP from LNS | 从LNS收到不支持的AVP | |
685 | Chap response from lns doesn't pass authentication | 从LNS收到reponse没有通过认证 | |
686 | The DAA user inbound car apply fail | DAA用户上行car 申请失败 | |
687 | The DAA user outbound car apply fail | DAA用户下行car 申请失败 | |
688 | The DAA user both direction car apply fail | DAA用户上下行car 申请失败 | |
689 | Server has no free ip for rui user | 框间借用场景server没有可分地址 | |
690 | Server select pool failed for rui user | 框间借用场景server匹配不到地址池网关 | |
691 | IP address conflict with Giaddr of the ip pool | IP地址和地址池的Giaddr参数冲突 | |
696 | Pwve-access interface bas disable | PWVE接入接口去使能BAS | |
710 | UP blocked | UP阻塞 | |
711 | Cusp state down | cusp状态down | |
712 | Framed IP conflicts with IP of interface | radius下发IP与UP的接口IP冲突 | |
713 | UP VPN instance not exist | UP侧VPN实例不存在 | |
714 | CP and UP vpn relate fail | CP与UP关联VPN失败 | |
717 | subscriber:fq:Unsupported fq name. | Radius下发subscriber:fq属性下发了不支持的fq队列名。 | |
740 | DHCPv6 user trigger fail for server configuration unconsistent | DHCPv6用户备机触发上线失败因为server配置不一致 | |
741 | ND user trigger fail for server configuration unconsistent | ND用户备机触发上线失败因为server配置不一致 | |
743 | Alloc Tunnel ID Fail | 分配隧道ID失败 | |
744 | L2TP NOT Enable or No L2TP License when processing SCCRQ | 处理SCCRQ时L2TP未使能或者L2TP license没有激活 | |
745 | There is no host name in SCCRQ | SCCRQ未携带主机名 | |
746 | Get L2TP group fail from host name when processing SCCRQ | 从主机名中获取L2TP组失败 | |
747 | L2TP NOT Enable or No L2TP License when processing ICRQ | 处理ICRQ时L2TP未使能或者L2TP license没有激活 | |
748 | Tunnel down when processing ICRQ | 处理ICRQ时隧道中断 | |
749 | CHAP authentication of the Web user is denied | web用户的CHAP认证拒绝 | |
752 | WEB authentication request is denied when processing authentication request | web用户的认证拒绝 | |
756 | Layer3-subscriber does not support pd user | 三层接入不支持PD用户 | |
757 | Relay Forward have no valid linkaddress | relay头无有效linkaddress地址 | |
773 | Static users fail to occupy exclusive address pool | 静态用户占用独享地址池失败 | |
774 | Static user access from shared address pool failed | 静态用户不支持从共享地址池上线 | |
775 | Add nat user data fail(IP Access User Limit) | 添加NAT用户失败(用户接入限制) | |
782 | The number of services exceeds limit | 业务数目超出限制 | |
789 | Prefix conflict with same option | 主备机相同option的前缀冲突 | |
790 | Prefix conflict with different option | 主备机不相同option的前缀冲突 | |
791 | CGN user does not support warm-standby switch | CGN用户不支持温备用户切换 | |
792 | Portswitch fail for reach slot access limit or slave interface not prepared | 温备端口切换预处理时达到单板接入限制或者备接口未配置cu-mode | |
793 | Radius authorize invalid vlan | RADIUS下发VLAN不合法 | |
831 | IP address conflict with static bind | IP 地址与静态绑定的地址冲突 | |
832 | IP address status is disable | IP 地址状态为disable | |
833 | RADIUS server delivered zero lease | Radius下发0租期 | |
834 | AMv6 with check fail | UM和AMv6表项一致性检查失败 | |
835 | Configuration recovery is not complete when processing SCCRQ | 处理SCCRQ报文时,配置恢复没有完成。 | |
836 | Multi-sessions per-mac exceed the maximum | 一mac多session上线的session数超过设置的最大值 | |
837 | The shared-key of RADIUS server has not been config | 未配置服务器秘钥 | |
838 | The route cost of the tunnel source interface bound to the L2TP group is invalid. | L2tp-group路由cost值无效。 | |
839 | DHCP users option82 mismatch | DHCP用户的option82信息不匹配 | |
840 | DHCPV6 check fail. | 表项一致性检查失败 | |
841 | The authenticator header of the RADIUS response packet is invalid. | RADIUS响应报文的认证字无效 | |
842 | PCP port range specified by RADIUS is out of reserved scope. | RADIUS端口段不在PCP保留端口段中。 | |
843 | Invalid PCP port range. | RADIUS下发的端口范围无效。 | |
844 | Fail to allocate PCP port. | PCP用户上线申请端口失败。 | |
845 | Dynamic Pool is not supported by Radius | radius不支持叠加全局地址池 | |
846 | Ucm receive repeated dhcpv6 connect request | UM 收到重复的dhcpv6的连接请求 | |
847 | Web user logout, pre-domain IPV6 authorization disabled. | Web用户下线,前域未配置IPV6授权。 | |
848 | AM with smooth fail | AM ip地址平滑失败 | |
849 | A subnet conflict occurred in the dynamic address pool | 动态地址池网段冲突 | |
850 | The vBRAS-UP specification is exceeded during a switchover in warm backup mode | 温备切换时超过UP设备规格 | |
851 | The number of users on the vBRAS-UP exceeds the specification | UP设备用户数超过规格 | |
852 | The number of IP stacks on the vBRAS-UP exceeds the specification | UP设备IP栈数超过规格 | |
853 | The number of IPv6 addresses on the vBRAS-UP exceeds the specification | UP设备IPv6地址数超过规格 | |
854 | CM with AAA start acct ack time out. | CM等待AAA计费回应超时 | |
855 | Receive PADI packet from user while user online | 用户在线时收到PADI报文 | |
856 | An IPv4 static user has a higher priority than the dynamic user with the same MAC address | 相同MAC的IPv4静态用户优先级比动态用户高 | |
857 | Port switch preprocessing fails during the PWVE online process | 端口切换预处理时PWVE上线处理失败 | |
858 | Port switch preprocessing fails during the PWVE offline process | 端口切换预处理时PWVE下线处理失败 | |
859 | DHCPv6 proxy lease expired | DHCPv6代理租期到期 | |
860 | The IP address assigned in the offer packet is inconsistent with that of the online user | SERVER在OFFER报文中给用户分配的IP地址与在线用户不一致 | |
861 | Disaster recovery group role change to slave | 灾备组降备 | |
862 | AMV6 with smooth fail | 与AMV6平滑数据失败 | |
863 | No service location is available | 没有可用的service location | |
864 | Interface information is invalid during a switchover in warm backup mode | 温备切换时接口信息无效 | |
865 | License not enable during a switchover in warm backup mode | 温备切换时单板未使能license | |
866 | Authentication methods are different during a switchover in warm backup mode | 温备切换时接口认证方式不同 | |
867 | Access data is invalid during a switchover in warm backup mode | 温备切换时接入数据无效 | |
868 | Qos information is different during a switchover in warm backup mode | 温备切换时接口QOS信息不一致 | |
869 | The address pool bound to the domain does not match the address pool bound to the interface. | 域和接口的地址池不匹配 | |
870 | Virtual MAC does not exist in peer CP | 用户的虚MAC在对端CP不存在 | |
871 | Virtual MAC conflicts with peer CP | 用户的虚MAC和对端CP的虚Mac有冲突 | |
872 | Acct-Session-Id conflict | 计费ID冲突。 | |
873 | MSEADA failed to download table | 适配下发表项失败 | |
SC_PROTOCOL_SERVICE_UNAVAILABLE(15) | 107 | L2TP service is unavailable | 业务不支持 |
SC_PROTOCOL_USER_ERROR (17) | 23 | PPP with authentication fail | 认证失败或超时 |
35 | EAPOL with authentication fail | 认证失败 |
对应的Radius标准原因码 | Subcode | 原因解释 | 备注 |
|---|---|---|---|
SC_PROTOCOL_LOST_CARRIER(2) | 523 | ND table synchronization fails | ND表项同步失败 |
SC_PROTOCOL_SESSION_TIMEOUT (5) | 312 | EAPOL server session timeout | EAPOL服务器端会话超时 |
SC_PROTOCOL_ADMIN_RESET (6) | 72 | DHCP free lease with command | DHCP管理员使用命令行收回IP地址 |
SC_PROTOCOL_NAS_ERROR(9) | 38 | EAPOL with nas error | 内部错误下线 |
64 | CM with Nas error | 内部错误下线,例如内存申请失败 | |
76 | AAA with memory alloc fail | 动态内存分配失败 | |
85 | AAA with timer create fail | 启动定时器失败 | |
153 | L2TP FSM error | 内部状态机不对 | |
163 | L2TP inner error | 内部处理出错 | |
167 | L2TP other error | 内部错误包括申请内存失败, 指针空等 | |
342 | L2TP alloc sessionid fail | L2TP分配会话id失败 | |
343 | L2TP alloc tunnelid fail | L2TP分配隧道id失败 | |
344 | L2TP init tunnel struct fail | L2TP初始化隧道数据结构失败 | |
345 | L2TP rebuild tunnel fail | L2TP重建隧道失败 | |
346 | L2TP download lac fib fail | L2TP下发lLAC转发表项失败 | |
347 | L2TP send SCCRQ fail | L2TP发送SCCRQ失败 | |
349 | L2TP get tunnel fail | L2TP获取隧道信心失败 | |
350 | L2TP remote slot | L2TP远端隧道板Down | |
427 | L2TP send connect up message fail | L2TP发送连接UP消息失败 | |
428 | L2TP send SCCCN fail | L2TP发送SCCCN失败 | |
430 | L2TP SCCRQ check fail | L2TP检查SCCRQ报文失败 | |
431 | L2TP SCCRP send fail | L2TP发送SCCRP报文失败 | |
SC_PROTOCOL_NAS_REQUEST (10) | 20 | Connect check fail | 表项一致性检查失败 |
24 | PPP with connect check fail | 表项一致性检查失败 | |
28 | L2TP with connect check fail | L2TP表项一致性检查失败 | |
30 | ARP with table full | ARP表项满 | |
31 | ARP with connect check fail | 同步表项失败 | |
32 | ARP with start detect fail | ARP开始探测失败(未知原因) | |
37 | EAPOL with connect check fail | 表项检查失败 | |
39 | SRVCFG with connect check fail | 表项一致性检查失败 | |
42 | MCC with nas error | 内部错误 | |
47 | MCC with mvlan update fail | MVLAN更新失败 | |
52 | AM with check fail | 表项一致性检查失败 | |
56 | CM with start arp detect fail | 启动arp探测失败 | |
61 | CM with add to FC fail | FC下发失败 | |
62 | CM with FC connect check fail | 调用FC表项检查返回失败 | |
63 | CM with AAA connect check fail | 调用AAA函数表项检查返回失败 | |
66 | Abnormal logout request packet | 收到异常logout请求报文 | |
73 | DHCP with unknown error | DHCP未知错误 | |
109 | DHCP cib syn error | DHCPACC处理UCM发来的表项同步信息,检测出有错 | |
111 | DHCP memory error | CODING-PROC-ADD, 内部错误, 创建定时器失败, 分配内存失败时使用 | |
112 | DHCP relay discovery pkt fail | 转发DISCOVER报文失败 | |
113 | DHCP create timer fail | 创建定时器失败 | |
114 | DHCP generate discover pkt fail | 构造DISCOVER报文失败 | |
115 | DHCP generate request pkt fail | 构造SELECT-REQUEST报文失败 | |
116 | DHCP send ack pkt fail | 发送ACK报文失败 | |
117 | DHCP send offer pkt fail | 发送OFFER报文失败 | |
118 | DHCP send message fail | 发送消息失败 | |
120 | DHCP packet info did not match | 收到REBOOT-REQ报文,有表项,检查报文信息不一致 | |
123 | DHCP caching client packet failed | DHCP缓存报文失败 | |
124 | DHCP storing user info failed | 存储用户信息到表项失败 | |
125 | DHCP distributing route failed | 发布路由失败 | |
126 | DHCP retrieved unexpected IP address | 触发上线获取的不是预期的IP地址 | |
127 | DHCP allocating IP from local pool failed | IP分配失败,只在本地地址池有效 | |
128 | DHCP user state timeout | 表项超时 | |
129 | DHCP receive other client's request packet | 收到客户端选择的REQUEST,但本服务器并非其选择的目标服务器 | |
131 | DHCP failed to relay selectReq to server | DHCP中继转发失败 | |
132 | DHCP sending reboot pkt fail | 向Server转发Reboot Request报文失败 | |
133 | MSEADA with user added fail | 适配下发转发表项失败 | |
134 | MSEADA with cib checked fail | 适配检查CIB失败 | |
136 | AAA with HQOS filled fail | AAA填充HQos授权信息失败 | |
137 | AAA with pool filled fail | AAA填充地址池授权信息失败 | |
138 | MSEQOS with SQ reserved fail | MSEQOS预先分配SQ资源失败 | |
140 | Failed to realtime backup | 表项实时备份添加失败 | |
141 | Layer2 leased line down | 二层专线下线引起的专线下用户下线 | |
147 | PPP up recv lcp again | 当ipcp up之后收到lcp阶段的协商报文(term除外) | |
157 | L2TP connect check fail | 表项一致性检查失败 | |
178 | ND Table Check Fail | 同步表项失败 | |
179 | ND send ipv6 request message fail | ND用户发送地址请求消息失败 | |
180 | ND Add Prefix Fail | 添加ND前缀失败 | |
181 | Prefix Aging | Prefix老化导致下线 | |
187 | MIP check fail | MIP 表项检查失败 | |
188 | MP first link down | MP第一个用户发生失败引起其他用户Down | |
191 | Clear VSI, BCP users offline | 清除VSI时候导致用户下线 | |
192 | Reserved | 预留 | |
193 | Update TBMASK fail | 更新TBMASK失败 | |
194 | Add ELB fail | 添加ELB 失败 | |
195 | Not support BCP access | 不支持BCP接入 | |
196 | Delete ELB fail | 删除ELB失败 | |
197 | Clear mac fail | 清除MAC失败 | |
198 | UCM beyond vsi limit | 超出的VSI的整机的规格 | |
201 | RUI users create ppp table fail | RUI触发PPPoE时,生成PPP相关表项失败原因 | |
202 | RUI users delete ppp table fail | RUI触发PPPoE时,删除PPP相关表项失败原因 | |
204 | Reserved | 预留 | |
206 | SRVCFG failed to process | 获取配置信息失败 | |
211 | Reserved | 预留 | |
212 | AAA service change | 业务切换 | |
214 | Fail to transport access type | 接入方式修改失败 | |
215 | Fail to check ucm oper | 适配校验UCM发送来的添加CIB消息失败 | |
216 | Fail to Init cib list | 初始化CIB全局指针数组失败 | |
217 | Fail to Init Cib | 初始化CIB失败 | |
218 | Fail to add mac hash | MAC哈希添加失败 | |
219 | Fail to add ip hash | IP哈希添加失败 | |
220 | Fail to set local cid from global cid | 设置槽位CIB失败 | |
221 | Fail to add internal pfb | 转发表下发失败 | |
222 | Fail to trans access type | 删除接口接入类型失败 | |
223 | Fail to check ucm oper message | 适配校验UCM发送来的删除CIB消息失败 | |
224 | Fail to del internal pfb | 转发表删除失败 | |
225 | Fail to del mac hash | MAC哈希删除失败 | |
226 | Fail to del ip hash | IP哈希删除失败 | |
227 | Fail to check ucm oper message when modify | 适配校验UCM发送来的modify CIB消息失败 | |
228 | Fail to get cib item when modify | 获取用户CID信息失败 | |
229 | Fail to set local CID from gloabal cid | 设置槽位cib失败 | |
230 | Fail to update internal pfb | 转发表项更新失败 | |
231 | Fail to update qos para | Qos参数更新失败 | |
232 | Fail to add user mac | 用户MAC添加失败 | |
233 | Fail to add arp | 添加芯片检测失败 | |
234 | Fail to add l2tp lac fwd table | 下发LAC用户转发表失败 | |
235 | Fail to add l2tp lns fwd table | 下发LNS用户转发表失败 | |
236 | Fail to add l2tp lts fwd table | 下发LTS用户转发表失败 | |
237 | Fail to add elabel map | ELA map下发失败 | |
238 | Fail to add outsegment table | 添加出方向转发表上失败 | |
239 | Fail to add insegment table | 添加入方向转发表失败 | |
240 | Fail to qinq user oper | 添加QinQ用户失败 | |
241 | Trunk is no member | Trunk下没有成员端口 | |
242 | Fail to resource Apply | 转发表项资源申请失败 | |
243 | Fail to set qos data | Qos数据设置错误 | |
244 | Fail to apply stat ingress res | 上行统计资源申请失败 | |
245 | Fail to apply stat egress res | 下行统计资源申请失败 | |
246 | Fail to apply new user mac index | 用户mac表索引申请失败 | |
247 | Fail to apply new arp index | 用户arp表索引申请失败 | |
248 | Fail to appy car id | Car id 申请失败 | |
249 | Fail to apply user-queue resource | 用户队列资源申请失败 | |
250 | The label cell is null | 表项没有空间 | |
251 | Fail to apply qos resource | Qos资源申请失败 | |
252 | Fail to apply qos res by host | Host Qos资源申请失败 | |
253 | Fail to apply qos res ingress | 上行Qos资源申请失败 | |
254 | Fail to apply stat res | 统计资源申请失败 | |
255 | Fail to apply staid ingress | 上行统计资源申请失败 | |
256 | Fail to apply statid egress | 下行统计资源申请失败 | |
257 | Fail to apply stat res ingress | 上行统计资源申请失败 | |
258 | Fail to apply qos res egress | 下行Qos资源申请失败 | |
259 | Fail to apply qos res by location | Qos资源申请失败 | |
260 | Fail to apply qos res by hash | Qos 资源申请失败 | |
261 | Fail to apply qos res by c-vlan | C-VlanQos 资源申请失败 | |
262 | Fail to apply qos res by lease line | 专线Qos 资源申请失败 | |
263 | Fail to manage internal qos resource | Qos 资源申请失败 | |
264 | Fail to portal add user info | 用户portal信息添加失败 | |
265 | Fail to add qos param | Qos 参数下发失败 | |
266 | Fail to download out bound SQ id | SQ下行下发失败 | |
267 | Fail to add fwd table | 添加转发表项失败 | |
268 | Fail to add internal product main fwd entry | 添加转发表项失败 | |
269 | Fail to add node fresh list | 刷新链表节点添加失败 | |
270 | Fail to deliver QoS parameters | Qos 参数下发失败 | |
276 | RUI trigger to delete pppoe cib failed | RUI触发用户删除cib失败 | |
277 | RUI trigger to create pppoe cib failed | RUI触发用户添加cib失败 | |
279 | User info is conflict with rui user | ucm 已有表项与RUI用户冲突 | |
280 | Rui is disable in the domain | 域下未使能RUI导致RUI触发用户认证失败 | |
281 | Fail to get rui user info | 取RUI触发用户信息失败 | |
282 | Record in aaa of rui authentication request is null | AAA存储的认证请求为空 | |
283 | Fill rui user information fail | 填充RUI触发用户信息失败 | |
284 | Fill rui user ip pool fail | 填充RUI触发用户pool 信息失败 | |
285 | Fill rui user qos profile fail | 填充RUI触发用户qos-profile 信息失败 | |
286 | RUI request cold backup user offline for slave | RBP进入Slave状态,通知冷备用户下线 | |
287 | IPv6 address allocation failed because of inner cause | 内部原因导致IPV6地址分配失败 | |
288 | No prefix available | 无可分前缀 | |
289 | No IPv6 address available | 无可分IP | |
290 | IPv6 address conflicts too much times | 超过配置的冲突次数 | |
291 | No available prefix for conflicts of the interface id specified by radius | Radius下发的接口ID与分配的前缀组成的地址发生冲突时 无可分配的前缀 | |
292 | User expected a wrong prefix length | 用户请求的前缀长度错误 | |
293 | MSEADA fail update qos resource | MSEADA 更新Qos资源失败 | |
294 | MSEADA fail update work slot | MSEADA 更新工作槽位失败 | |
295 | MSEADA success update work slot | MSEADA 更新工作槽位完成 | |
296 | Failed to update ip address for ip type mismatch | 因为地址类型不匹配导致更新地址失败 | |
297 | Failed to update user mac table | 更新用户mac表失败 | |
298 | AAA update ipv6 address fail | 更新ipv6地址失败 | |
299 | UCM failed to send ipv6 update message to AAA | UCM向AAA发送ipv6更新消息失败 | |
300 | UCM failed to send ipv6 update message to MSEADA | UCM向适配发送ipv6更新消息失败 | |
301 | UCM update ipv6 address fail | UCM更新ipv6地址失败 | |
302 | UCM with framed IPv6 address invalid | 下发的ipv6地址和本地的冲突 | |
307 | MSEADA failed to download session table | 适配下发session表项失败 | |
308 | MSEADA failed to download uaib table | 适配下发uaib表项失败 | |
309 | MSEADA failed to download cib table | 适配下发cib表项失败 | |
310 | MSEADA failed to add cid from vcd | 适配添加cib表项失败 | |
311 | DHCPV6 check fail | 表项一致性检查失败 | |
313 | UCM portswitch process fail | UCM端口切换处理失败 | |
314 | UCM portswitch preprocess fail | UCM端口切换处理失败 | |
315 | MSEADA portswitch process fail | 适配端口切换处理失败 | |
316 | MSEADA portswitch process timeout | 适配端口切换处理超时 | |
317 | MSEADA set user num of interface fail | 适配设置接口用户数失败 | |
318 | MSEADA portswitch notify access module fail | 适配通知接入模端口切换失败 | |
324 | DHCPV6 inner error | DHCPV6内部未知错误 | |
327 | Get Interface Linklocal Addr Failed | 获取上线接口的LINKLOCAL地址失败 | |
328 | Base service address alloc failed | 基础协议栈分配失败 | |
340 | IPv6 static user has a higher priority than dynamic user with same mac | 相同mac的IPv6静态用户优先级比动态用户高 | |
348 | L2TP session limit | L2TP会话数限制 | |
351 | Failed to switch workslot for user is not up | 槽位切换失败 | |
354 | MSEADA failed to get lns info | 获取lns信息失败 | |
355 | MSEADA failed to download l2tp global table | 下发单板上Tunnel-session表项失败 | |
356 | MSEADA failed to download l2tp global table | 下发单板上Tunnel-session表项失败 | |
357 | MSEADA failed to get pfb data | 释放转发表空间失败 | |
358 | MSEADA failed to download dual user table | 双栈用户添加转发表失败 | |
359 | AAA with DAA QOS filled fail | AAA填充DAA的Qos信息失败 | |
360 | Fail to get ppp info when modify | 修改用户信息时,获取ppp信息失败 | |
361 | PPP is already down when modify | 修改用户信息时,PPP链路已经Down掉 | |
362 | Failed to add user to board for user is not up | trunk成员端口变化引起的用户下线 | |
363 | Authentication method error on bas interface | 接口配置的认证方式错误 | |
364 | EAP connection down | EAP 连接Down | |
368 | GTL license needed | 缺少GTL license | |
369 | Online user number exceed GTL license limit | 上线用户数超过GTL license允许数量 | |
370 | User access speed too fast | 用户上线速率太快 | |
371 | Bas interface access limit | bas接口接入限制 | |
372 | Wait cib ack time out | 等待cib回应超时 | |
373 | Wait EAPOL auth request time out | 等待EAPOL认证请求超时 | |
374 | Wait EAPOL down ack time out | 等待EAPOL下线回应超时 | |
375 | Wait WEB auth request time out | 等待WEB认证请求超时 | |
376 | Wait WEB down ack time out | 等待WEB下线回应超时 | |
377 | Wait WEB user ack time out | 等待WEB用户回应超时 | |
378 | Wait PPP auth request time out | 等待PPP认证请求超时 | |
379 | Wait L2TP connection up time out | 等待L2TP连接建立超时 | |
380 | Wait DHCP connection request time out | 等待DHCP连接请求超时 | |
383 | Board type does not support user access | 单板不支持用户接入 | |
384 | Slot blocked | 单板冻结 | |
385 | Fail to switch workslot for slotcid is invalid | slotcid无效导致主处理板切换失败 | |
390 | Get dslite info error | 获取dslite信息错误 | |
391 | Get nat info error | 获取nat信息错误 | |
393 | CM with CGN ack time out | UCM等待CGN回应超时 | |
394 | Add nat user data fail | 添加NAT用户失败 | |
395 | Add nat user data fail(Input Error) | 添加NAT用户失败(输入错误) | |
396 | Add nat user data fail(Create User Fail) | 添加NAT用户失败(创建用户失败) | |
397 | Add nat user data fail(Port PreAlloc Fail) | 添加NAT用户失败(端口与分配失败) | |
398 | Add nat user data fail(Syn User To Spu Fail) | 添加NAT用户失败(同步用户失败 | |
399 | Not Find User When Del CGN User | 要删除的CGN用户不存在 | |
400 | Add nat user data fail(Search Public Addr Fail) | CGN单板查找用户的公网地址池失败 | |
401 | IPv4 user basic ip type and author mismatch | ipv4基础协议类型与授权不匹配 | |
402 | IPv6 user basic ip type and author mismatch | ipv6基础协议类型与授权不匹配 | |
403 | Add nat user data fail(add slave user fail) | 添加NAT用户失败(CGN备板/备框上线失败) | |
404 | Add nat user data fail(public resource conflict) | 添加NAT用户失败(公网资源冲突) | |
405 | IPv6 PD user basic ip type and author mismatch | ipv6 pd基础协议类型与授权不匹配 | |
406 | IPv6 user managed flag error | ipv6用户管理状态标志错误 | |
407 | CM with CGN modify time out | UCM等待CGN修改回应超时 | |
408 | L2TP RUI IN BATCH BACKUP | L2TP RUI处于主备机数据同步时期 | |
409 | Fail to download daa car param | 下发DAA的CAR参数失败 | |
410 | Fail to apply daa qos resource | 应用DAA的Qos资源失败 | |
411 | Fail to apply daa inbound qos resource | 应用DAA上行Qos资源失败 | |
412 | Fail to apply daa outbound qos resource | 应用DAA下行Qos资源失败 | |
413 | Fail to apply count resource | 统计管理资源失败 | |
414 | Static on-line user with the same mac exists | 存在相同MAC的静态用户 | |
415 | Packet Authenticator Error | 报文验证字错误 | |
418 | Basic stack IPv6 address alloc fail | 作为基础协议栈的IPv6地址分配失败 | |
419 | Basic stack PD prefix alloc fail | 作为基础协议栈的PD前缀分配失败 | |
420 | L2TP test tunnel ok | L2TP 测试隧道成功 | |
421 | L2TP test tunnel NG | L2TP测试隧道失败 | |
423 | L2TP tunnel time out | L2TP隧道超时拆除 | |
424 | General error occured in modify process | 更新流程出错 | |
425 | CM with user blocked | 用户被阻塞 | |
426 | L2TP local clear tunnel | L2TP本端清除隧道 | |
429 | L2TP wait auth ack timeout | L2TP等待认证回应超时 | |
433 | Up to user max session | 达到最大用户Session数 | |
434 | Can not get all of authorized IP address | 未获取到所有授权IP地址 | |
436 | IPv4 authentication method error | IPv4认证方式配置错误 | |
437 | IPv6 authentication method error | IPv6认证方式配置错误 | |
438 | DHCPv6(IANA) can't access with ND at the same time | DHCPv6(IANA)不能和ND同时接入 | |
439 | PPP IPCP negotiate fail | PPP用户IPCP协商失败 | |
440 | PPP IPv6CP negotiate fail | PPP用户IPv6CP协商失败 | |
441 | ND address conflict | ND地址冲突 | |
442 | ND Repeat Request | 收到用户重复的ND请求 | |
443 | CGN auto cut | CGN公网用户自动回切 | |
444 | The ds-lite tunnel prefix length is inconsistent with the user's | Ds-lite中配置的隧道前缀长度和用户下发给CGN业务板的前缀长度不一致 | |
445 | L2TP Tunnel password error | L2TP隧道密码错误 | |
446 | L2TP Tunnel authentication fail | L2TP隧道认证失败 | |
447 | User's password expired | 用户密码过期 | |
448 | The VPN to which the subscriber belongs has been deleted. | 用户所在VPN被删除 | |
449 | DHCPV6 packet speed limit | DHCPV6报文限速 | |
450 | PPP IPCP terminate | PPPIPCP终结下线 | |
451 | PPP IPv6CP terminate | PPPIPv6CP终结下线 | |
452 | The number of users on this slot exceeds limit | 当前单板上的用户数已超出限制 | |
453 | Fail to save ucm message data | 添加UCM消息内容失败 | |
454 | The number of classifiers in a packet exceeded the specification | 一个分类器中规则数目超过规格 | |
455 | The number of classifiers in a packet exceeded the specification | 一个分类器中规则数目超过规格 | |
456 | The same classifiers could not use different behavior names | 不允许相同分类器使用不同动作 | |
457 | The number of classifiers delivered by a device exceeded the specification | 整机下发的分类器数目将超过规格 | |
458 | The number of user groups of a device exceeded the specification | 整机user-group数目将超过规格 | |
459 | The number of classifier referenced by all-user exceeded the specification | 整机的用户CB对引用超过规格 | |
460 | The number of classifier referenced by per-user exceeded the specification | 用户CB对引用超过规格 | |
461 | The number of the classifier's rules exceeded the specification | 远端classifier中的rule超过规格 | |
462 | The attribute identifiers were not registered | 属性携带的参数未注册 | |
463 | The ACL type was invalid | 属性携带的ACLtype参数无效 | |
464 | The classifier name was invalid | 属性携带的classifier参数无效 | |
465 | The behavior name was invalid | 属性携带的behavior参数无效 | |
466 | The optype value was invalid | 属性携带的optype参数无效 | |
467 | The ruleid value was invalid | 属性携带的ruleid参数无效 | |
468 | The sipv4 value was invalid | 属性携带的sipv4参数无效 | |
469 | The sipv6 value was invalid | 属性携带的sipv6参数无效 | |
470 | The dipv4 value was invalid | 属性携带的dipv4参数无效 | |
471 | The dipv6 value was invalid | 属性携带的dipv6参数无效 | |
472 | The ss-group value was invalid | 属性携带的ss-group参数无效 | |
473 | The ss-group does not exist | 属性携带的ss-group不存在 | |
474 | The su-group value was invalid | 属性携带的su-group参数无效 | |
475 | The su-group does not exist | 属性携带的su-group不存在 | |
476 | The value of the ds-group was invalid | 属性携带的ds-group参数无效 | |
477 | The ds-group does not exist | 属性携带的ds-group不存在 | |
478 | The du-group value was invalid | 属性携带的du-group参数无效 | |
479 | The du-group does not exist | 属性携带的du-group不存在 | |
480 | The proto value was invalid | 属性携带的proto参数无效 | |
481 | The sport value was invalid | 属性携带的sport参数无效 | |
482 | The dport value was invalid | 属性携带的dport参数无效 | |
483 | The sport-range value was invalid | 属性携带的sport-range参数无效 | |
484 | The dport-range value was invalid | 属性携带的dport-range参数无效 | |
485 | The pre value was invalid | 属性携带的pre参数无效 | |
486 | The tos value was invalid | 属性携带的tos参数无效 | |
487 | The dscp value was invalid | 属性携带的dscp参数无效 | |
488 | The tcpflag value was invalid | 属性携带的tcpflag参数无效 | |
489 | The remark-dscp value was invalid | 属性携带的remark-dscp参数无效 | |
490 | The value of remark-ipv6-dscp was invalid | 属性携带的remark-ipv6-dscp参数无效 | |
491 | The remark-8021p value was invalid | 属性携带的remark-8021p参数无效 | |
492 | The dir value was invalid | 属性携带的dir参数无效 | |
493 | An ACL delivered multiple duplicate attributes | 同一条ACL中有多个属性重复出现 | |
494 | The parameters delivered could not be the same | 同一个ACL里包含的属性不支持重复下发 | |
495 | An unregistered attribute was displayed in RC | RC中出现了未注册的属性 | |
496 | The protocol was not TCP when the tcpflag was delivered | 协议和tcpflag属性值冲突 | |
497 | The port and protocol type conflicted | 协议和端口属性值冲突 | |
498 | The address type defined in an ACL and protocol type conflicted | ACL地址类型和协议属性值冲突 | |
499 | The address type defined in an ACL and IP address type conflicted | ACL地址类型和ip类型属性值冲突 | |
500 | An unregistered attribute was displayed in RB | RB中出现了未注册的属性 | |
501 | An unregistered attribute was displayed in lc or optype | LC或Optype中出现了未注册的属性 | |
502 | One packet contained multiple optype parameters | 一个报文包含多个optype属性 | |
503 | The lc and other attributes in an ACL were mutually exclusive | 同一个ACL中lc参数和其它参数互斥 | |
504 | The permit and deny in an ACL were mutually exclusive | permit和deny互斥 | |
505 | The IPV4 and IPv6 in an ACL were mutually exclusive | ipv4和ipv6互斥 | |
506 | One ACL could not deliver multiple source types | 同一条ACL中不能下发多个源类型 | |
507 | One ACL could not deliver multiple destination types | 同一条ACL中不能下发多个目的类型 | |
508 | The dport and dport-range in one ACL were mutually exclusive | 同一条ACL中dport和dport-range互斥 | |
509 | The sport and sport-range in one ACL were mutually exclusive | 同一条ACL中sport和sport-range互斥 | |
510 | The bidirectional parameter and rule ID in an ACL were mutually exclusive | 同一条ACL中下发bi-dir参数和ruleid参数互斥 | |
511 | The tos or pre parameter and dscp parameter was mutually exclusive | 同一条ACL中dscp参数和tos或pre参数互斥 | |
512 | Ipv6 and tcp-flag in the same ACL were mutually exclusive | 同一条acl中tcpflag和ipv6互斥 | |
513 | IP address alloc fail for IP pool is synchronizing | 地址池同步导致地址分配失败 | |
514 | The user was logged out due to web packet attacks | Web报文抑制下线 | |
515 | LNS Multicast user resource full | LNS组播用户统计资源申请失败 | |
518 | Fail to create dynamic user-group | 创建动态user-group失败 | |
519 | Dynamic user-group number is full | 动态user-group已达到规格数 | |
521 | Fail to release the public IP | 释放公网IP地址失败 | |
524 | Web fast reply was configured on the L2-aware user access board. | L2-aware用户接入单板配置了WEB快回 | |
538 | Failed to authorize session group user | Session group用户授权失败 | |
539 | No sub user in session group | 家庭中没有子用户 | |
540 | Username user cannot switch to session group user | Username用户不能变更为sessiong group用户 | |
542 | Session group user doesnot support reauthentication | session group用户不支持重认证 | |
548 | Undo NAT server | 命令行删除nat server 发起用户下线 | |
555 | Receive LCP terminate request from user while LCP negotiating. | LCP协商阶段收到用户LCP终止请求 | |
556 | Receive LCP terminate request from user after IPCP negotiation. | IPCP协商后收到用户LCP终止请求 | |
558 | Receive PADT packet from user | 收到用户PADT报文 | |
559 | Receive PADR packet from user while user online | 用户在线时收到PADR报文 | |
560 | OFFER packet contains a gateway IP address | SERVER在OFFER报文中给用户分配的IP地址是网关IP | |
561 | OFFER packet contains an IP address not on user segment | OFFER中分配的IP地址不属于用户所在网段 | |
562 | OFFER packet contains an IP address being used | 正在使用的IP地址被OFFER报文分配给了其他用户 | |
563 | OFFER packet contains a conflicting IP address | OFFER报文中给用户分配的IP地址正在被他人使用 | |
565 | ACK packet contains a gateway IP address | ACK报文中分配的IP地址是网关IP | |
573 | DHCP wait authentication reply timeout | DHCP等待认证超时 | |
574 | DHCP wait Up reply timeout | DHCP等待UP超时 | |
575 | Fail to alloc specified IP address for RUI | RUI备机分配指定IP地址失败 | |
580 | DHCP Server no response. | DHCP服务器无响应 | |
582 | ACK packet has an IP address being used by other user | ACK中分配的IP地址被其他人占用 | |
583 | IP address record fail on local device | 本地记录远端分配的IP地址失败 | |
631 | MSEADA failed to check qvct table | 适配检查QVCT表项失败 | |
635 | Online interface is conflict with family | 上线接口与家庭冲突 | |
644 | TERM with time out | TERM模块定时器超时 | |
649 | UCM failed to apply resource for virtual-access user | 更新虚拟接入用户资源失败 | |
660 | Virtual-access remote interface bas disable | 虚拟接入外联口去使能BAS | |
661 | UCM failed to get resource parameter for virtual-access user smooth | 虚拟接入用户平滑时获取资源参数失败 | |
662 | UCM failed to get interlink for virtual-access user smooth | 虚拟接入用户平滑时获取内联口失败 | |
668 | CGN instance is synchronizing data | CGN实例正在同步数据 | |
670 | CM with CGN syn ack time out | UCM等待CGN同步回应超时 | |
671 | CM with CGN del ack time out | UCM等待CGN删除回应超时 | |
672 | CM failed get nat instance when smooth | 平滑的时候获取nat实例信息失败 | |
673 | CM with VSM connect check fail | 调用VSM函数表项检查返回失败 | |
678 | LNS tunnel name doesn't match LAC remote-name | LNS的隧道名与LAC的远端名不匹配 | |
680 | Use config to create tunnel with no start lns ip-address | 用配置创建隧道时没有起始的lns的ip地址 | |
681 | Invalid tunnel id from LNS SCCRP | LNS SCCRP的隧道ID无效 | |
692 | UCM failed to apply resource for pwve user | 更新PWVE接入用户资源失败 | |
693 | UCM failed to apply nhp resource for pwve-access | PWVE接入申请NHP资源失败 | |
694 | UCM failed to get resource parameter for pwve-access user smooth | PWVE接入用户平滑时获取资源参数失败 | |
695 | The user was logged out due to pwve-access interface no nexthop | 由于没有下一跳出接口用户下线 | |
697 | User offline for test command | TEST命令行用户下线 | |
698 | Check user board resource failure | FEI/UM表项同步FEI表项不存在用户下线 | |
699 | MSEADA failed to download user-mac table | 适配下发USER-MAC表项失败 | |
700 | MSEADA failed to download AIB table | 适配下发AIB表项失败 | |
701 | MSEADA failed to download CST table | 适配下发CST表项失败 | |
702 | CM with qos ack time out | 添加用户表项等待qos回应超时 | |
703 | CM with qinq ack time out | 添加用户表项等待qvct回应超时 | |
704 | CM with fei ack time out | 添加用户表项等待fei回应超时 | |
705 | VSM reset section user down | VSM删除地址池用户下线 | |
706 | Add nat user data fail(slave VPN mismatch) | 添加NAT用户失败(CGN备板/背框VPN不匹配) | |
707 | RUI data synchronization | RUI表项同步 | |
708 | Dual previous check failed | 双栈预检查失败 | |
715 | The port license is not active | 端口license没有激活 | |
716 | CM failed get dslite instance when smooth | 平滑的时候获取dslite实例信息失败 | |
718 | subscriber:fq:More blanks exist. | Radius下发subscriber:fq属性pbs,weight前的分隔空格多于1个 | |
719 | subscriber:fq:The shaping and shaping-percentage can not be together. | Radius下发subscriber:fq属性shaping 和perctange同时下发 | |
720 | subscriber:fq:Shaping range error. | Radius下发subscriber:fq属性Shaping的范围不正确 | |
721 | subscriber:fq:Pbs range error. | Radius下发subscriber:fq属性Pbs的范围不正确 | |
722 | subscriber:fq:Unsupported sch. | Radius下发subscriber:fq属性下发了不支持的调度方式 | |
723 | subscriber:fq:Wfq must with weight. | Radius下发subscriber:fq属性wfq方式的调度方式没有下发weight | |
724 | subscriber:fq:Non-wfq can't with weight. | Radius下发subscriber:fq属性非wfq方式的调度方式下发weight | |
725 | subscriber:fq:Weight range error. | Radius下发subscriber:fq属性weight的范围不正确 | |
726 | subscriber:fq:Direction error. | Radius下发subscriber:fq属性下发了不支持的方向 | |
727 | subscriber:fq:Unsupported function. | Radius下发subscriber:fq属性下发了不支持的其它功能 | |
728 | subscriber:fq:Neither shaping nor sch. | Radius下发subscriber:fq属性既没有shaping也没有sch | |
729 | subscriber:fq:The ratio of the shaping values exceeds 2000. | Radius下发subscriber:fq属性多个属性间shaping的比值超过2000倍 | |
730 | subscriber:fq:Unsupported user type. | Radius对不支持的用户类型下发了subscriber:fq属性 | |
731 | subscriber:fq:Incompatible FQ scheme. | Radius下发subscriber:fq属性和上线用户欲生效qos-profile下配置的fq模板存在 | |
732 | subscriber:fq:No QoS-profile error. | Radius对没有qos,即不限速用户下发subscriber:fq属性 | |
733 | subscriber:fq:Get QoS-profile error. | Radius下发subscriber:fq属性获取用户qos时出错 | |
734 | subscriber:fq:Car speed limit error. | Radius对car限速用户下发subscriber:fq属性 | |
735 | subscriber:fq:queue in car mode. | Radius下发subscriber:fq属性同时上线用户欲生效qos-profile下配置的fq队列存在以car实现shaping的格式 | |
736 | The number of users on this card exceeds limit | 当前子卡上的用户数已超出限制 | |
739 | Delete domain force user to offline | 域删除强制用户下线 | |
750 | The Web user is authenticated when processing CHAP authentication request | 正在处理该web用户的CHAP认证 | |
751 | The Web user is being authenticated when processing CHAP authentication request | 该web用户的CHAP认证已完成 | |
753 | The Web user is authenticated when processing authentication request | 正在处理该web用户的认证 | |
754 | The Web user is being authenticated when processing authentication request | 该web用户的认证已完成 | |
755 | Over limit of users and NOT EAP USER | 非EAP用户 | |
758 | Portswitch process fail for synchronize interface information | 端口切换处理时同步接口信息失败 | |
759 | Portswitch process fail for send roam up ack message | 端口切换处理时发送漫游上线回应消息失败 | |
760 | Portswitch process fail for modify user host router | 端口切换处理时用户路由变更失败 | |
761 | Portswitch process fail for synchronize physical information | 端口切换处理时同步物理信息失败 | |
762 | Portswitch process fail for L2TP process | 端口切换时L2TP处理失败 | |
763 | Portswitch preprocess fail for trunk offline process | 端口切换预处理时TRUNK离线处理失败 | |
764 | Portswitch preprocess fail for free QOS resource | 端口切换预处理时释放QOS资源失败 | |
765 | Portswitch preprocess fail for reach slot access limit | 端口切换预处理时达到单板接入限制 | |
766 | Portswitch preprocess fail for apply QOS resource | 端口切换预处理时申请QOS资源失败 | |
767 | Portswitch preprocess fail for trunk online process | 端口切换预处理时TRUNK上线处理失败 | |
768 | Portswitch preprocess fail for synchronize physical information | 端口切换预处理时同步物理信息失败 | |
769 | Portswitch preprocess fail for reach interface access limit | 端口切换预处理时达到接口接入限制 | |
770 | Portswitch preprocess fail for user add access number | 端口切换预处理时用户更新接入计数失败 | |
771 | Portswitch not support dhcpv6 access when switching | 端口切换时不支持dhcpv6接入 | |
772 | Switch domain is suppressed because HA is not done | 主备倒换平滑过程中不允许web用户登录后域 | |
775 | Add nat user data fail(IP Access User Limit) | 添加NAT用户失败(用户接入限制) | |
776 | FES message queue blocked | FES消息队列积压 | |
777 | FEI add service table failed | 下发增值业务业务表项失败 | |
778 | FEI add service action table failed | 下发增值业务动作表项失败 | |
779 | Family is conflict with edsg | 家庭表项冲突 | |
780 | Family table cannot be created | 家庭表项无法创建 | |
781 | Family table cannot be updated | 家庭表项无法更新 | |
783 | Failed to refresh service table | 刷新业务表项失败 | |
784 | Failed to backup message | 备份消息失败 | |
785 | Failed to apply qos when modify | modify流程申请qos资源失败 | |
786 | UM wait fei ack time out | 等待FEI回应超时 | |
787 | Access types of the CP and UP do not match | CP和UP侧的接入类型不匹配 | |
788 | Pipeline inner error | 管道内部错误 | |
789 | Prefix conflict with same option | 主备机相同option的前缀冲突 | |
790 | Prefix conflict with different option | 主备机不相同option的前缀冲突 | |
794 | DB request offline | DB恢复用户请求下线 | |
795 | User info is conflict with DB | ucm 已有表项与DB用户冲突 | |
796 | CU does not support L2TP's IPV6 users online. | CU不支持L2TP的IPV6上线 | |
797 | User access conflicts with key configuration modification. | 上线过程中关键配置变更冲突 | |
798 | L2TP LNS BackupGrp Session Backup Fail | LNS备份会话失败 | |
799 | UCM failed to apply resource for lns backup user | 更新lns备份用户资源失败 | |
800 | The number of L2NAT users exceeds limit | L2NAT用户数超出限制 | |
801 | Portswitch preprocess fail for reach interface ip-stack access limit | 端口切换预处理时达到接口IP栈接入限制 | |
802 | Failed to acquire a valid user name template | 获取用户名模板失败 | |
803 | The UP types do not match for warm backup | 温备组下主备接口所属UP的UP类型不一致 | |
804 | The interface type does not support warm backup | 接口类型不支持温备,vup上接口不是pwve口 | |
805 | The PW-VE tunnel type must be VXLAN for warm backup. | 温备的pwve口只支持vxlan隧道类型 | |
806 | The interface types do not match | 接口类型不匹配 | |
807 | The access type does not support warm backup | 接入类型不支持温备 | |
808 | The backup interface of the faulty interface fails to be obtained | 获取不到与故障口为备份关系的接口 | |
809 | The domain configurations are different for warm backup | 温备组下主备接口的域配置不同 | |
810 | User info is conflict with online user | 上线用户信息与已在线用户冲突 | |
811 | The interface is not ready now | 接口还没有就绪 | |
812 | The board is not available | 单板不可用 | |
813 | The count of IPoE user has reached the maximum number of board | 单板的IPoE用户数已经达到最大值 | |
814 | Layer 3 static users with vpn-instance switch enabled do not support RUI | 三层静态用户动态下发VPN不支持RUI | |
815 | The address carried in ack packet is different from offer packet | ACK报文中分配的IP地址与OFFER报文不一致 | |
816 | L2TP session state synchronization failed during failover | L2TP故障转移会话状态同步失败 | |
817 | L2TP failover recovery failed | L2TP故障转移恢复失败 | |
818 | L2TP failover recovery timed out | L2TP故障转移恢复时间超时 | |
819 | L2TP tunnel is in the failover recovery phase | L2TP隧道正处于故障转移恢复阶段 | |
820 | Vxlan state down | Vxlan状态down | |
821 | DHCP request packet contains a unmatched IP address | Request请求IP与在线用户IP不匹配 | |
822 | UCM inner error | UCM内部错误 | |
823 | Failed to resume dynamic subnet from server | 动态地址池网段恢复失败 | |
825 | CGN instance down(static-mapping configured with load-balance) | CGN实例状态不可用(配置了静态溯源算法叠加负载分担) | |
826 | Cold backup user IP address conflict | 冷备场景下用户地址冲突 | |
827 | The Dynamic pool has no license and no other pools are avaliable. | 动态地址池未使能license,并且其他地址池都不可用 | |
828 | Incomplete user ip stack | 用户IP栈信息不完整 | |
829 | No available DHCPV6 server | 没有可用DHCPV6 server | |
830 | Dynamic subnet conflicts in disaster recovery | 灾备场景动态地址池网段冲突 | |
874 | The RBP resources on the UP plane are insufficient | UP面RBP资源不足 | |
875 | Get warm profile group failed. | 温备IPOE 一MAC多session场景,基于接口获取温备组索引失败 | |
876 | The ODAP client fails to detect the server | odap地址池探测失败 | |
877 | Online users on the same interface and in the same VLAN conflict | 当client-replace enable 命令生效时,从同接口同vlan上线不同mac地址用户,老用户下线 | |
880 | Dynamic server has no subnet with matching length | 动态地址池服务器配置掩码长度和请求长度不一致 | |
881 | Dynamic server no avaliable subnet | 动态地址池服务器没有可用网段 | |
882 | User login from basic IP stack times out | 等待基础协议栈上线超时 | |
883 | KeepOnline static user detect fail | 配置了KeepOnline的静态用户探测失败 | |
884 | Login from the second stack (IPv6) is not allowed during port switching | 端口切换时不支持第二栈(IPv6)接入 | |
885 | The dynamic subnet lease timeout | 动态地址池续租失败 | |
886 | The dynamic subnet renew failed with error subnet state | 动态地址池服务器侧网段状态错误导致网段续租失败 | |
887 | The dynamic subnet renew failed with no exsited subnet | 续租网段在服务器侧不存在 | |
888 | Ipv6 address delivered by Radius conflicted with DHCPv6 server pool address | Radius下发的地址与DHCPv6地址池地址冲突 | |
889 | The user group from UP is not configured on CP | CGN用户上线时,UP面上报的user-group在CP面没有配置 | |
890 | Static mapping bind load balance | 不支持负载分担的静态溯源NAT | |
891 | Up is not ready | Up未上报License支持能力给CP | |
892 | The address of the online user is different from that assigned by the DHCPv6 server. | 在线用户地址与DHCPV6 server分配地址不一致. | |
893 | Dynamic server is smoothing | 动态地址池申请网段失败,因为DAP-Server侧处于平滑状态 | |
894 | Dynamic server is locked | 动态地址池申请网段失败,因为DAP-Server侧处于lock状态 | |
895 | User virtual mac is different with user identifier | 用户虚mac与用户分类信息不一致 |
Subcode | 原因解释 | Subcode | 细化后原因解释 | 细化后原因解释 |
|---|---|---|---|---|
21 | 用户主动下线 | 555 | Receive LCP terminate request from user while LCP negotiating. | LCP协商阶段收到用户LCP终止请求 |
556 | Receive LCP terminate request from user after IPCP negotiation. | IPCP协商后收到用户LCP终止请求 | ||
558 | Receive PADT packet from user | 收到用户PADT报文 | ||
559 | Receive PADR packet from user while user online | 用户在线时收到PADR报文 | ||
58 | CM模块定时器超时 | 560 | OFFER packet contains a gateway IP address | SERVER在OFFER报文中给用户分配的IP地址是网关IP |
561 | OFFER packet contains an IP address not on user segment | OFFER中分配的IP地址不属于用户所在网段 | ||
562 | OFFER packet contains an IP address being used | 正在使用的IP地址被OFFER报文分配给了其他用户 | ||
563 | OFFER packet contains a conflicting IP address | OFFER报文中给用户分配的IP地址正在被他人使用 | ||
564 | OFFER packet has an IP address being used by PPPoE user | OFFER中分配的IP地址被PPPoE用户占用 | ||
565 | ACK packet contains a gateway IP address | ACK报文中分配的IP地址是网关IP | ||
566 | ACK packet contains an IP address being used | 正在使用的IP地址被ACK报文分配给了其他用户 | ||
567 | ACK packet contains a conflicting IP address | ACK报文中给用户分配的IP地址正在被他人使用 | ||
568 | ACK packet has an IP address being used by PPPoE user | ACK中分配的IP地址被PPPoE用户占用 | ||
569 | RADIUS allocated address not matching the trigger one | RADIUS下发的IP地址与触发用户不一致 | ||
570 | No available pool for the Layer3 DHCP user | 三层DHCP用户找不到可用地址池 | ||
571 | No available pool for the Layer2 DHCP user | 二层DHCP用户找不到可用地址池 | ||
572 | Server-Identifier in packet is not the local device | SERVER IDENTIFIER非设备上的IP | ||
573 | DHCP wait authentication reply timeout | DHCP等待认证超时 | ||
574 | DHCP wait Up reply timeout | DHCP等待UP超时 | ||
60 | 地址分配失败 | 575 | Fail to alloc specified IP address for RUI | RUI备机分配指定IP地址失败 |
576 | No available pool | 无可用地址池 | ||
577 | The idle addresses conflict with those used by other users | 空闲的IP地址实际被设备其他用户占用 | ||
578 | ACK contains a gateway IP address not matching the user's | ACK报文中携带的网关与用户的网关不匹配 | ||
579 | ACK packet contains a mask not matching the user's | ACK报文中的掩码与用户掩码不一致 | ||
580 | DHCP Server no response. | DHCP服务器无响应 | ||
581 | ACK packet contains an IP address not on user segment | ACK中分配的IP地址不在用户网段内 | ||
582 | ACK packet has an IP address being used by other user | ACK中分配的IP地址被其他人占用 | ||
583 | IP address record fail on local device | 本地记录远端分配的IP地址失败 |
2、本资源基本为原创,部分来源其他付费资源平台或互联网收集,如有侵权请联系及时处理。
3、本站大部分文章的截图来源实验测试环境,请不要在生产环境中随意模仿,以免带来灾难性后果。
转载请保留出处: www.zh-cjh.com珠海陈坚浩博客 » Radius协议规定的标准停止计费原因
作者: 小编
| 手机扫一扫,手机上查看此文章: |
一切源于价值!
其他 模板文件不存在: ./template/plugins/comment/pc/index.htm